5466-032 Woodward speed control module

Price:

Product basic information
Manufacturer: Woodward
Model: 5466-032
Belonging to the famous 505 series
Supports multiple communication protocols and can be smoothly integrated with the existing control system of the factory
Core application: Designed specifically for speed control and protection of steam turbines
5466-032 controller has stable performance and high reliability

Categories: WOODWARD
Tags: - Actuator 5466-032 controller debugger module Motor touch screen WOODWARD

5466-032 Woodward speed control module

The 5466-032 is a microprocessor-based digital governor controller produced by Woodward, belonging to its classic 505 series.
It is primarily designed for speed control and protection of steam turbines. Below is a detailed introduction to this product:

I. Product Overview

Brand and Model: Woodward 5466-032
Series: 505 Series Digital Governor
Type: Microprocessor-based controller
Purpose: Specifically designed for steam turbines to control their speed and provide overspeed protection.

II. Core Functions

Speed Control:
- 5466-032 Precisely controls the speed of steam turbines by adjusting steam inlet flow.
- Supports single-range or split-range actuators to accommodate turbines of different sizes.
Overspeed Protection:
- Incorporates triple independent overspeed protection logic to ensure rapid shutdown in case of overspeed, preventing equipment damage.
- Provides an overspeed test button for convenient on-site testing of protection functions.
Emergency Shutdown:
- Equipped with an emergency stop button for immediate shutdown in emergency situations.
System Protection:
- - Automatically switches control modes upon sensor failure to ensure uninterrupted system operation.
  - Offers local/remote control priority selection to adapt to different operational scenarios.

For lower gate drivers, the 0.4 ohm impedance of the driver can keep the gate of the power MOSFET below the threshold level to ensure that

no through current occurs during high dV/dT phase node transitions. The internal diode charging bootstrap capacitor enables the device to use

N-channel MOSFETs in a half bridge configuration. The tri state pulse width modulation (PWM) input provided by TPS28225 is compatible with all multi-phase controllers such

as TITPS40091. The power-off mode can protect the load from the influence of reverse output voltage.

The TPS28225 MOSFET driver is now in mass production and can be ordered through TI and its authorized distributors. This device is available in two packaging versions

: a low-cost 8-pin SOICDFN package and a heat dissipation enhanced 3mm x 3mm 8-pin DFN package.

IR2117 is a gate driver integrated circuit designed by IR Corporation in the United States specifically for driving individual MOSFETs or IGBTs. IR2117 is a gate driver designed by IR

Corporation in the United States specifically for driving single MOSFETs or IGBTs. It uses high-voltage integrated circuit technology and latch free CMOS technology, and adopts a

dual in-line package, which can be used in systems with working bus voltages up to 600V. Its input is compatible with standard CMOS levels, and its output driving characteristics can meet the

design requirements of high current driven output stages with the shortest cross conduction time. The application of its floating channel and bootstrap technology allows it to be directly

used to drive an N-channel MOSFET or IGBT that operates on the high or low side with a bus voltage of up to 600V.

2. Internal structure and working principle

The internal structure and working principle diagram of IR2117 are shown in Figure 2. It integrates nine unit circuits internally, including a Schmitt trigger, a pulse gain circuit, two undervoltage

detection and protection circuits, a level shift network, a NAND gate, a complementary power amplifier output stage composed of two MOSFETs, an RS trigger, and a pulse filter.

During normal operation, if the logic power supply and output power supply of IR2127 are not under voltage, the signal from the user controlled pulse forming unit is first shaped by a Schmitt trigger,

then amplified by a pulse gain loop, and level shifted and matched by a level shift network. After being triggered by an RS trigger, it is output by a complementary push-pull output stage to drive an external MOSFET or

IGBT. Once either the input logic power supply or the output amplifier stage floating power supply experiences undervoltage, one of the output signals

will be blocked, causing the output drive pulse to become low level.

III. Technical Specifications

Power Supply: 18-32 VDC, supporting 24VDC input.
Display: Two-line x 24-character LED display for clear indication of operating status and parameters.
Enclosure: NEMA 4X or IEC 60529 IP56 rated for protection against harsh industrial environments.
Inputs/Outputs:
- Inputs: 6 programmable current inputs, 16 discrete contact inputs.
- Outputs: 2 actuator outputs, 8 relay outputs, 6 programmable current outputs.
Communication Interfaces: 5466-032 Supports RS-232, RS-422, and RS-485 hardware interfaces for easy integration with host computers or other devices.
Software: Equipped with OpView™ and 505View software for parameter configuration, monitoring, and fault diagnosis.
Operating Temperature: -20 to +60°C (some models support -4 to +140°F).
Storage Temperature: -40 to +85°C (some models support -40 to +185°F).
5466-032 Weight: Approximately 9.11 pounds (4.13 kilograms).

IV. Application Scenarios

Steam Turbine Control: 5466-032Suitable for steam turbines of various sizes, including industrial steam turbines, small grid turbo-generators, and turboexpanders.
Single Extraction and Admission Applications: Designed for operating steam turbines in single extraction and/or admission applications.
On-Site Programming: Allows on-site operators to program and adjust parameters through an integrated operator control panel, adapting to different operating conditions.

V. Product Advantages

High Reliability:
- Microprocessor-based design ensures precise control and stability.
- Triple independent overspeed protection logic provides multiple layers of safety.
Flexibility:
- Supports various actuator and sensor configurations to accommodate different turbine models.
- Offers a rich set of input/output interfaces for easy system expansion and integration.
Ease of Use:
- Two-line x 24-character LED display provides an intuitive operating interface.
- A 30-key multifunctional keyboard simplifies parameter configuration and operation.
Compatibility:
- Supports multiple communication protocols for easy integration with DCS, PLC, and other systems.
- Provides OpView™ and 505View software for remote monitoring and fault diagnosis.